How to Build a Loft Bed With a Desk Underneath

A loft bed is a great space-saving solution for kids' rooms. Loft beds give your child a cool place to sleep and a handy place to do homework or hang out.


This loft bed features storage compartments in the stairs, a big desk and a fireman’s pole.
Tools and Materials:
  • Air compressor and hoses
  • Brad nailer
  • Circular saw
  • Finish nailer
  • Jig saw
  • Measuring tape
  • Orbital sander
  • Safety glasses
  • Speed square
  • T-square
  • Table saw
  • Plumb Bob or string line and weight
  • Screw gun
  • Eight sheets of 3/4” medium-density fiberboard (MDF)
  • Three sets of 22” drawer glides 
  • One 1-1/2" stainless steel pipe (normally used for a handrail)
  • Two 1-1/2" stainless steel pipe flanges
Steps:
1. Design and layout the bed. Allow enough height for your child to be able to sit up in bed. Our loft bed has a study area underneath. One end of the bed is held up by a desk with hutch, and the other end is held up by two bookshelf towers. Instead of a ladder, we built a staircase with the desk running right into one of the stair treads. As a special request, we also installed a fireman’s pole next to the bed.

2. Make a cut list by sketching out the design and determining how to assemble. 

3. Cut all the pieces using the table saw for long rips and the circular or miter saw for crosscuts. Make sure to mark everything to make assembly easier. It’s best to assemble the bed in sections then install them together inside the room.

4. Assemble the desk and stairs. The surface of the desk and the second stair tread is the same piece of wood. Thus, one side of the desk is held up by the lower staircase, and the other side is held up by two support pieces. There is no riser for the lower staircase; the sides will be open to provide storage. Build the bottom step with a riser and tread but leave the tread off the second step (the tread will be the end of the desk). Build the 4th, 5th and 6th steps as one piece, the bottom of which will sit on the desk and the top will meet the base of the bed. If you plan on painting the bed, face nail if you need to, then fill all the holes with wood filler and caulk all the seams.

5. The hutch is two simple bookshelves, so all the pieces will be assembled the same way. Lay out the sides of each unit then mark where you want the shelves to go. Glue and nail the shelves between the uprights. Assemble the MDF pieces using glue and a finish gun.
6. Cut the base of the bed frame about two inches bigger than the mattress – this allows enough extra space to tuck in the sheets. Create at least 6-inch side pieces to go around the base. You do not need a side piece for the backside of the bed. Create an additional safety railing for the front and if desired, the open end of the bed. Assemble using glue and a finish gun.

7. Fill in nail holes and caulk gaps, then prime and paint each piece. It’s best to do this outside -- you’ll have less mess to worry about.

8. Install each section of the loft bed, starting with the desk. Attach ledgers to the wall for the desk nailing it into the studs. Make sure the tops of the ledgers are at the same height as the top of the lower staircase piece. Attach the bottom of the staircase to the wall. Lay the surface of the desk on top of the ledgers and bottom steps then attach with wood glue and a nails.
9. Attach a ledger to the wall for the long side of the bed. Attach one of the bookshelf units to the ledger. Make sure they are level. Attach the base to the ledger and the top of the bookshelf. Attach the end piece of the base to the wall.
10. Attach the top part of the staircase nailing it into the desk and bed frame.
11. Slide the second (outer) bookshelf into place and fasten to the bed frame.
12. To install the fireman's pole, locate a ceiling joist. You need to attach the flange to a framing member. Drop a plumb line or weight on a string to find level spot. Mark the floor. Cut the pipe to length and insert it into the flanges and screw down the floor flange.

  • Digg
  • Del.icio.us
  • StumbleUpon
  • Reddit
  • RSS

How to Build a Day Bed

Step-by-step instructions for a couch/bed that will come in handy when guests are in town

If you don’t have the space for another guest bed, add a day bed. Here’s how to make one:
Materials and Tools:
  • table saw
  • miter saw
  • MDF (medium-density fiberboard)
  • 4 bun feet
  • 4 metal brackets
  • drywall screws
  • twin mattress
  • paint or batting and fabric
Steps:
1. To build the outer frame, cut two side rails (10 by 76 inches) and two end rails (10 by 37 inches). Cut two larger pieces of MDF to fit inside the frame to create the platform that the mattress will rest on.
2. Cut 1-by-1-inch cleats to support the platform and install them 1½ inches down from the top along the side and end rails. Leave a gap along the side rails that’s about 24 inches from each end to allow two cross pieces to be installed to support the center of the platform boards.
3. To hold the cross supports, attach more 1-by-1 cleats 1½ inches up from the bottom around the perimeter. Cut the two cross supports.
4. Flip the day bed over and attach a metal bracket to each corner on the outer edge of the frame. Screw the feet into position. Turn the day bed back over. Slide the cross supports into position and slide the platform pieces into position to check the fit.
5. Paint or upholster the day-bed frame (staple batting over the frame, and then cover it with fabric) as desired.

  • Digg
  • Del.icio.us
  • StumbleUpon
  • Reddit
  • RSS

Coastal Cottage-Style Shutter Headboard

Easily create this inexpensive yet impressive headboard using unfinished shutters, paint and sandpaper.

Shutter Headboard+

Materials Needed:

  • unfinished, louvered shutter doors (available at most home improvement stores)
  • screwdriver
  • (2) 2-1/2" screws and coordinating anchors
  • hammer
  • drill
  • several small mending braces and screws
  • aerosol spray primer
  • pint latex paint, in the color and finish of your choice
  • 2" wide paintbrush
  • sanding block
  • 8-grit sandpaper
  • ventilation mask
  • plastic drop cloth

Measure Bed

Measure the width of the bed to determine how many (and what width) shutters to purchase.

Prepare Shutters for Painting

Remove hinges and door knobs then place the shutters on a large plastic drop cloth.
  • View: Remove the HardwareImage 1
  • View: Paint PreparationImage 2
  • Remove the Hardware+

Prime Shutters

Wearing a ventilation mask, lightly coat the front and sides of each shutter with spray primer. It's okay if bare wood shows through in places to add to the antique look. Tip: To prevent drips, hold the can approximately 12 inches away from shutters when spraying, and move the can in smooth, sweeping motions.
Spray Primer on the Shutters 

Paint Shutters

Once the primer has completely dried, use a 2-inch wide paintbrush to coat the shutters with paint. To create a weathered look, load the brush with paint, then wipe some of it off onto a paper towel before applying it to the shutters — this technique is called "dry brushing" and allows some of the primer and wood color to show through. Allow paint to dry completely before moving onto the next step.
  • View: Paint the ShuttersImage 1
  • View: Allow the Paint to DryImage 2
  • Paint the Shutters+

Sand Shutters

Use a sanding block wrapped in 80-grit sandpaper to remove painted areas and increase the weathered look. Tip: Concentrate your sanding efforts on areas that would have seen the most wear, such as the outside edges of each shutter and the front edge of louvers.
Add Age to the Shutters+

Attach Mending Braces

Use small mending braces to join the shutters together. For maximum stability, add a mending brace to the top, middle and bottom of each shutter.
Apply Braces to the Shutters 

Pre-Drill Holes

Move shutter headboard into place behind bed. Drill a hole through the shutter and into the wall to mark where the wall anchor should go.
Attach and Drill Headboard into the Wall+

Embed Wall Anchors

Pull shutter headboard away from wall and drive anchors, one in each top corner, into the pre-drilled holes in wall.
Hammer in the Wall Anchors+

Securely Attach Shutter Headboard to Wall

Put shutter headboard back into place and drive a 2-1/2 inch screw through the front of the shutter and into the anchors embedded in the wall.
Position the Headboard

  • Digg
  • Del.icio.us
  • StumbleUpon
  • Reddit
  • RSS

How to Build a Wrought Iron Panel Headboard

Create a custom headboard with lumber and wrought iron panels.


Materials and Tools:
  • 1 x 8 poplar boards
  • wrought iron panels  
  • biscuit joiner  
  • biscuits
  • wood glue
  • decorative molding
  • miter saw
  • finish nails
  • drywall screw
  • drill
Steps:
1. Measure the bed's width, add one inch on each side and cut the top and bottom boards. Cut two side rails that are long enough so the metal panels will rest on lumber with an equal edge on all sides. Cut two interior boards to the necessary length.
2. Use a biscuit joiner, biscuits and wood glue to connect the bottom board to the vertical pieces. Repeat for the top of the frame.
3. Cut trim to size to create an outer frame on the top and side boards. Attach it with wood glue and finish nails.
4. Finish with paint or stain as desired and let dry.
5. Use drywall screws to attach the panels directly to the front of the headboard.

  • Digg
  • Del.icio.us
  • StumbleUpon
  • Reddit
  • RSS

How to Build a Contemporary Style Bedside Table

Basic cabinet boxes are built then accented with an exotic hardwood to create high-end looking nightstands.


Tools and Materials:
  • 3/4” meranti (an exotic hardwood from the Philippines) plywood
  • 3/4” solid poplar
  • 1/2” prefinished maple plywood
  • 18” full extension drawer glides
  • Brad nailer with 2” brad nails and 1-3/8” pin nails
  • power drill with 1” wood screws and 1-1/2” wood screws
  • countersink bit
  • pocket jig
  • sander and sandpaper
  • paint, polyurethane and painting supplies
  • wood putty and wood glue
  • table saw and a miter saw
  • tape measure
  • safety glasses
Steps:
1. Build the cabinet box using the 3/4’ solid poplar. On a table saw, cut the pieces to size:
-   top: 19-1/4” x 36”
-   two side pieces: 19-1/4” x 21-1/4”
-   inner shelf and bottom piece: 18-1/2” x 34-1/2”
-   back: 21-1/4” x 36”
2. Attach the top, shelves and sides to the back with wood glue and 2” brad nails. Set the inner shelf 8-7/8 inches from the top, and attach the bottom shelf 1 inch from the bottom.
3. Build the two drawer boxes using the 1/2” prefinished maple. On a table saw, cut the pieces to size:
-   two drawer bottoms: 17” x 32-1/2”
-   four drawer fronts and backs: 8” x 32-1/2” 
-   four drawer sides: 18” x 8”
4. Assemble the drawer boxes. On the inside of the front, back and side pieces, make a 1/2” dado cut a 1/2" from the bottom. Fasten the two sides and the back together. Slide the bottom drawer piece into the dado groove then attach the front piece.
5. Attach the drawer glides to the cabinet box and drawer sides with wood screws.
6. To build the drawer fronts, cut two pieces of poplar at 10” x 36”. Cut two pieces of meranti at 1” x 36” and another two pieces of meranti at 4-1/4” x 36”.
7. Center the 1-inch piece of meranti on the poplar piece (5 inches on center). Attach the two pieces with glue and brad nails. Then center the 4-1/4” piece of meranti on top of the 1-inch piece, glue and nail together. To give the drawer pulls extra support, insert wood screws from the back into all three pieces of wood.
8. Fill in any nail holes with wood putty and sand the surfaces. Stain and varnish, let dry completely.
9. Attach the drawer fronts to the drawer boxes with glue and brad nails. The fronts should sit flush with the bottom and sides of the drawer. For extra support, use wood screws to secure the fronts to the drawer from the inside of the drawer.

  • Digg
  • Del.icio.us
  • StumbleUpon
  • Reddit
  • RSS

Easy To Make Corbel Bedside Tables

Spruce up your bedroom with easy-to-make decorative bedside tables. They take less than a weekend to make and cost less than $100 in materials.

To make this space-saving table, a store-bought corbel is topped off with plywood and decorative molding.
Materials and Tools:
  • two corbels
  • thin molding
  • birch plywood
  • table or circular saw
  • wood glue
  • nail gun and nails
  • screw gun and screws
Steps:
1. Determine the size of the table, cut the plywood to that size for the tabletop. We made our table 10” x 12”.
2. Cover the exposed plywood edges with molding. Use wood glue and a nail gun to attach the molding. Only cover the front and two sides, the backside will be pressed against the wall.
3. Attach the corbel to the tabletop using wood glue and a nail gun.
4. Paint or stain the wood as desired and let it dry completely. We painted ours white.
5. If the corbel has a keyhole notch in the back, insert a screw into the wall so that you can slip the corbel onto the wall. If your table is wide, you may also have to hang a cleat on the wall to support the tabletop.

  • Digg
  • Del.icio.us
  • StumbleUpon
  • Reddit
  • RSS

Build an Easy to Make Slatted Headboard

Add instant charm and personality to your bedroom with a wooden headboard. It takes less than a weekend to build and less than $100 in materials.

A headboard can add sophistication to any plain bedroom.
Tools and Materials: 
  • 16 clear pine 1x4s
  • dark stain, paintbrushes and rags
  • chop saw
  • wood glue
  • nail gun
  • screw gun and screws
Steps: 
1. Decide how large you would like your headboard to be. Typically the headboard is as wide as the bed, but it can look nice extra long or extra short, depending on the design and style of your room.
2. Cut the desired amount of slats to the appropriate length, miter cut the end of each slat. The slats in our headboard are 1-1/2” thick. To save money we bought 1x4s and cut them in half lengthwise.
3. Cut two extra slats for the vertical pieces that will be used to hold all the slats together. These do not need to be miter cut.
4. Cut two inch returns for each side of each slat. Make a 45-degree cut at one end of each piece so it will fit snugly against the end of a slat. The flat side of the return will go against the wall. Use wood glue and a nail gun to attach the returns to the slats.
5. Sand all the pieces until smooth.
6. Stain all the pieces and let dry completely.
7. Line up all of the pieces of the headboard with the returns facing up (the front of the headboard facing down). Use uniform-size scrap blocks of wood in between each slat to make sure they are spaced evenly apart.
8. Lay the two vertical pieces across the slats making sure they are also evenly spaced. Screw the two vertical pieces to each slat, connecting the entire structure. Make sure the screws are not too long, you don’t want them poking through the front of the headboard.
9. Put the headboard in place. Make sure it is level before securing it in place with 3”-drywall screws. Drive the screws through the two vertical pieces and right into the wall studs.

  • Digg
  • Del.icio.us
  • StumbleUpon
  • Reddit
  • RSS